Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateGenie Torsion Spring Replacement: The Whitney Owner’s Guide
We replace Genie torsion springs for Whitney homeowners, and a typical installed job runs $180 to $340 depending on the spring size and door weight. Most calls we take in Whitney happen the same morning the door stops opening, so we keep those springs ready and finish the work in one visit. Your price is stated flat before we touch anything.
Owners usually find out this way: the door opens halfway and stops. Or they hit the button and hear a loud bang from above the door, then nothing moves. Sometimes the door creaks for a week first, then quits on a cold morning. Genie systems are common in Whitney, and a broken torsion spring is the single most frequent reason a Genie door stops working.
Which Genie Models This Applies To
If you have a Genie door system, there’s a good chance you’re dealing with a torsion setup. Genie’s chain-drive and belt-drive openers (the 2022, 2122, 3122, and QuietLift lines) pair with standard torsion assemblies on most residential doors. The opener model matters less than the spring itself, but the spring has to match your door.
Here’s the part that trips people up: Genie torsion springs aren’t universal. They’re sized by wire gauge, inside diameter, and length, and they’re wound left or right depending on which side of the center bracket they sit. Get any one of those wrong and the door either won’t lift or will wear the spring out inside a year. The spring’s specs are stamped on the winding cone or printed on a label inside the door frame. If you can read those numbers, we can match the spring before we arrive.
On the OEM-versus-aftermarket question: Genie-branded springs cost more and give you no real advantage over a quality American-made spring from a known mill. We install springs measuring the same coil count and wire size, sourced from manufacturers that hold the same tolerance as the factory part. You get the right spring, not a price tag for the logo.
We also service LiftMaster and Chamberlain systems if your home has more than one door.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Genie Torsion Spring Replacement Is Failing
The torsion spring is a coiled steel part above the door that carries most of the door’s weight. It winds tighter as the door closes and releases as it opens. When it fails, you’ll notice one or more of these:
- A loud bang from above the door. That’s the sound of the spring snapping, and it usually happens under tension while the door is down. Once it goes, the opener can’t lift the door by itself.
- The door opens partway and stops. A weakened or partially broken spring can’t counterbalance the door through its full travel. The opener hits its limit and reverses, or the motor strains and overheats.
- A visible gap in the coil. Look at the spring above the door. A clean break in the coil is unmistakable once you know what to look for. You’ll see two separate pieces where there should be one continuous coil.
- The door feels heavy when you lift it by hand. With the opener disengaged, a properly balanced door lifts with one hand and stays put when you let go. If it drops or feels like dead weight, the spring has lost tension.
- The door slams down instead of easing shut. A spring that’s lost tension lets gravity take over on the way down. That puts a hard load on the door panels, hinges, and opener rail every time it closes.
Any one of these is reason to stop using the door. Running a Genie opener against a broken spring burns the motor and can snap a cable.
Replacement Cost & What’s Included
In Whitney, a Genie torsion spring replacement runs $180 to $340, installed. That price is the flat quote we give before any work starts, and it covers the spring, the labor, and the winding. It doesn’t change once we’re on site unless the door itself is out of balance and needs adjustment beyond the spring.
What drives the range: spring size and wire gauge, whether you have a single spring or a pair, and how accessible the torsion assembly is. A standard single-spring door sits at the low end. A heavier double-spring setup or a low-clearance track sits higher. If your cables or bearings are also worn, we’ll show you what we see and quote that work separately before touching it.
Every spring replacement is covered by our 90-Day Done Right Promise. If it’s not right, we come back at no charge, in writing, no arguing.
Ask about our $50 Off Any Repair Over $250 and the standing 5% senior and veteran discount.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely look at the spring and read the label on the door frame. You can also test balance with the opener disengaged and the door halfway up. That’s the limit of what we’d advise.
Torsion springs hold the full weight of your door under heavy tension. Winding one with the wrong bars, or letting a bar slip, can break a wrist or worse. We’ve seen Whitney homeowners try it and end up with a bent door and a hospital bill that dwarfs the repair. This is not a job for a YouTube tutorial. It requires the right winding bars, the right spring specs, and the kind of care that comes from doing it hundreds of times. That’s what we do.
Call us at (844) 797-9248 and we’ll talk through what you’re seeing. We schedule same-day service when the schedule allows and quote a flat price up front.
FAQs
Standard torsion springs last roughly 10,000 open-and-close cycles, or about 7 to 10 years in most Whitney homes. Whitney’s summer heat and dry air can shorten that, and we see springs fail closer to the 6- to 8-year mark on doors facing west. A high-cycle spring upgrade will roughly double the lifespan if you use the door heavily.
Call (844) 797-9248 for a quote on either option. Estimates are free.
No. A broken or tired torsion spring can’t be welded, re-wound, or patched with any reliability. It’s a single-use load-bearing part, and the only sound repair is replacement. Trying to re-tension a weakened spring is how injuries happen.
Call (844) 797-9248 and we’ll tell you exactly what needs to go.
A standard single-spring replacement takes about 45 minutes to an hour, and most Whitney jobs are finished in one visit because we carry the springs we need. A double-spring or out-of-balance door can run longer, and we’ll tell you the window when we quote.
Call (844) 797-9248 to schedule.
We match the spring by wire gauge, inside diameter, length, and wind direction from what’s on your door, then install a spring from a mill we trust at that exact spec. You get the correct part for your Genie door, not a one-size guess. We’re an independent service company and not affiliated with Genie, so our only job is matching your door right.
Call (844) 797-9248 for a free estimate. We’ll be there when we say.
Let’s Get That Door Working
If your Genie door stopped working and you’re in Whitney, call us today. A live person answers around the clock, and there’s no phone tree. Call (844) 797-9248.
Written by the team at Mainspring Garage Door Co. Whitney, serving Whitney and nearby areas.